`

avaya基本配置方法

阅读更多
ctrl+e
用户名:dadmin
密码:jrj123
pin:jrj1234
4410

查看开长途没有
cha sta 8328 8328
cor  1 不能打  2 能打长途

查看掩饰号码
cha pub 0/1/2

查看出局:
cha  pub 4 ext 分机
F3保存

查看入局
cha inc tru 1/2(分别2个组)

F7--下一页  F8 上一页

4600 IVR组

save  t  保存

山东AVAYA设备
172.29.10.170
dadmin
dadmin01
sat
dadmin01
w2ktt

测试通道
status trunk 1
跟踪分机状态
list trace station 4427
查看板卡信息
list configuration stations
查看板卡状态
list cor
查看异地出具的归属
cha station ****
更改cor以后就可以异地出局
test bo 1a08
test bo 1a09
test bo 1a10
test bo 1a11ch
查看板卡组状态
st sig 3
st sig 4
st sig 5
st sig 6

status aesvcs link 检查aes连接情况

list hunt-group 查看ivr组
change inc-call-handling-trmt trunk-group 4 更改呼入ivr组指向

list configuration carrier 板卡号 查看板卡配置信息
list configuration all 查看所有板卡配置
status media-processor all 查看所有media板卡
status media-processor board 7a13 查看板卡信息
test board 7a13 测试板卡状态
display errors 查看错误
display alarms 查看告警
list ipserver-interface 查看ip卡
list ip-interface all 查看c-lan板卡,media-pro板卡
list public-unknown-numbering 查看出局号
change public-unknown-numbering ext-digits 8402 0 更改出局号
monitor traffic trunk-groups 查看满线路情况
display sys cu 查看系统license
status trunk x 查看中继x各端口的状态

disp feature-access 查看外拨出局总号
disp dialplan analysis 查看外拨出局

display inc-call-handling-trmt trunk-group 4 查看入局落入分机组
cha inc-call-handling-trmt trunk-group 修改落入分机组,修改直拨电话使用

dup sta 3801 start 3701 board 03a07 count 100 批量添加100个分机在某一个分机板上
list sta 5771 count 10 查看从5771开始的10个分机

cha cor 11查看time of day chart
list partition-route-table查看路由表
list route-pattern 查看路由trunk表

配置ipsi卡
前提G650安装完毕加电
IPSI板卡插到G650网关的第一个槽位(支持热插拔)
笔记本连接到IPSI板卡前端的Service口(固定IP地址192.11.13.6)
Windows界面点击开始菜单-运行-cmd进入dos
ping 192.11.13.6如果可以ping通
telnet 192.11.13.6 回车
[IPSI]: ipsilogin
Login: craft
Password: serv1ces
[IPADMIN]: set control interface 198.152.254.203 255.255.255.0
[IPADMIN]: show control interface
[IPADMIN]: exit
telnet 192.11.13.6 回车
[IPSI]: ipsilogin
Login: craft
Password: serv1ces
[IPADMIN]: set control gateway 198.152.254.1
[IPADMIN]: show control gateway
[IPADMIN]: exit
添加cabinet
add cabinet *
Cabinet Layout:G650-rack-mount-stack

change system-parameters ipserver-interface允许IPSI控制端口网络
IPSI Control of Port Networks: enabled

add ipserver-interface PNnumber

List ipserver-interface查看IPSI注册状态

change system-parameters maintenance修改系统维护参数

change node-names ip
添加media板卡地址和名称
change circuit-packs *查看设备识别情况

音频流压缩
cha ip-network-region 1
==================================================================================
                               IP NETWORK REGION
  Region: 1
Location: 1       Authoritative Domain:
    Name: Main
MEDIA PARAMETERS                Intra-region IP-IP Direct Audio: yes
      Codec Set: 1              Inter-region IP-IP Direct Audio: yes
   UDP Port Min: 2048                      IP Audio Hairpinning? n
   UDP Port Max: 65535
DIFFSERV/TOS PARAMETERS                  RTCP Reporting Enabled? y
Call Control PHB Value: 46      RTCP MONITOR SERVER PARAMETERS
        Audio PHB Value: 46       Use Default Server Parameters? y
        Video PHB Value: 26
802.1P/Q PARAMETERS
Call Control 802.1p Priority: 6
        Audio 802.1p Priority: 6
        Video 802.1p Priority: 5      AUDIO RESOURCE RESERVATION PARAMETERS
H.323 IP ENDPOINTS                                       RSVP Enabled? n
  H.323 Link Bounce Recovery? y
Idle Traffic Interval (sec): 20
   Keep-Alive Interval (sec): 5
            Keep-Alive Count: 5                                      
=======================================================================================
cha ip-codec-set 1
=======================================================================================
                          IP Codec Set

    Codec Set: 1

    Audio        Silence      Frames   Packet
    Codec        Suppression  Per Pkt  Size(ms)
1: G.729             n         2        20
2:
3:
4:
5:
6:
7:


     Media Encryption
1: none
2:
3:
========================================================================================

配置trunk
1. 接入中继线
2. 添加中继板卡
add ds1 *******
name:*****
bit rate:2.048
line coding:hdb3
signaling mode:isdn-pri
country protocol:18
interface companding:alaw
idle code:01010110

3. test bo 中继板卡号,检查通畅情况(busyout 中继板卡号,release 中继板卡号)
4. add signal-group **
==================================================================================
SIGNALING GROUP

Group Number: 4              Group Type: isdn-pri
                    Associated Signaling? y          Max number of NCA TSC: 0
                       Primary D-Channel: 01A1316     Max number of CA TSC: 0
                                                   Trunk Group for NCA TSC:
       Trunk Group for Channel Selection:
      TSC Supplementary Service Protocol: a          Network Call Transfer? n
==================================================================================
5. cha trunk **,添加中继板卡号
6. status trunk **,查看trunk状态


配置IPtrunk
1. 接入clan板卡
add ip-interface 1a05
========add ip-interface 1a05=========================================================
IP INTERFACES


                  Type: C-LAN
                  Slot: 01A05
           Code/Suffix: TN799  D
             Node Name: clan(a05)
            IP Address: 172.29 .10 .175
           Subnet Mask: 255.255.255.0                            Link: 1
       Gateway Address: 172.29 .10 .1
  Enable Ethernet Port? y                       Allow H.323 Endpoints? y
        Network Region: 1                        Allow H.248 Gateways? y
                  VLAN: n                         Gatekeeper Priority: 5

Target socket load and Warning level: 400
       Receive Buffer TCP Window Size: 8320
                                ETHERNET OPTIONS
                  Auto? n
                 Speed: 100Mbps
                Duplex: Full
========================================================================================

2. 添加数据模块
add data-module 3100
========add data-module 3100============================================================
                              DATA MODULE

  Data Extension: 3100            Name: TO AES_1
            Type: ethernet
            Port: 01A0517
            Link: 1




Network uses 1's for Broadcast Addresses? y
========================================================================================

3. 添加signal-group
add signal-group 7
========add signal-group 7==============================================================
                                SIGNALING GROUP

Group Number: 7              Group Type: h.323
                           Remote Office? n          Max number of NCA TSC: 0
                                     SBS? n           Max number of CA TSC: 0
          IP Video? n                              Trunk Group for NCA TSC:
       Trunk Group for Channel Selection: 14
      TSC Supplementary Service Protocol: a          Network Call Transfer? n
                         T303 Timer(sec): 10

   Near-end Node Name: clan(a05)             Far-end Node Name: RemoteClan
Near-end Listen Port: 6510                Far-end Listen Port: 6510
                                        Far-end Network Region: 1
         LRQ Required? n                 Calls Share IP Signaling Connection? y
         RRQ Required? n
                                             Bypass If IP Threshold Exceeded? n
                                                      H.235 Annex H Required? n
         DTMF over IP: out-of-band            Direct IP-IP Audio Connections? y
Link Loss Delay Timer(sec): 90                         IP Audio Hairpinning? n
Enable Layer 3 Test? y                          Interworking Message: PROGress
                                         DCP/Analog Bearer Capability: 3.1kHz
========================================================================================
busy signaling-gr 7
rel  signaling-gr 7

4. 添加ip-codec-set
===add ip-codec-set 1 ===================================================================
                          IP Codec Set

    Codec Set: 1

    Audio        Silence      Frames   Packet
    Codec        Suppression  Per Pkt  Size(ms)
1: G.729             n         2        20
2:
3:
4:
5:
6:
7:                           
=========================================================================================

5. 添加trunk
===add trunk 14==========================================================================
                                TRUNK GROUP

Group Number: 14                   Group Type: isdn          CDR Reports: y
  Group Name: To_150_YiDong               COR: 1        TN: 1        TAC: 714
   Direction: two-way        Outgoing Display? n         Carrier Medium: H.323
Dial Access? n              Busy Threshold: 255  Night Service:
Queue Length: 0
Service Type: tie                   Auth Code? n
                                              Member Assignment Method: auto
                                                       Signaling Group: 7
                                                     Number of Members: 30

      Group Type: isdn

TRUNK PARAMETERS
         Codeset to Send Display: 6     Codeset to Send National IEs: 6
                                        Charge Advice: none
  Supplementary Service Protocol: a     Digit Handling (in/out): enbloc/enbloc


                                                   Digital Loss Group: 18
Incoming Calling Number - Delete:     Insert:                 Format:

Disconnect Supervision - In? y  Out? y
Answer Supervision Timeout: 0

TRUNK FEATURES
          ACA Assignment? n            Measured: both
                                 Internal Alert? n        Maintenance Tests? y
                               Data Restriction? n     NCA-TSC Trunk Member:
                                      Send Name: n      Send Calling Number: y
            Used for DCS? n                            Send EMU Visitor CPN? n
   Suppress # Outpulsing? n    Format: public
                                             UUI IE Treatment: service-provider

                                                 Replace Restricted Numbers? n
                                                Replace Unavailable Numbers? n
                                                      Send Connected Number: n
Network Call Redirection: none                    Hold/Unhold Notifications? n
             Send UUI IE? y                    Modify Tandem Calling Number? n
               Send UCID? n
Send Codeset 6/7 LAI IE? y
==========================================================================================

重置分机
busyou station ****
release station ****

配置分机内呼
cha aar an

不同pbx之间分机转呼
cha uniform-dial 0
cha aar an

设置分机之间的监听
cha cor *
修改cor:
Can Be Service Observed?是否被监听
Can Be A Service Observer?是否监听
修改监听码:
cha feature-access-codes

change system-parameters features
修改:
service obsevring:warning tone打成n

ip-trunk如果不输送主叫号码,cha trunk 1中的 Send Calling Number: n没有设置成y


====================命令解锁================================
1. 查看在线用户
status logins
2. reset log **

==========================================================
内部分机互通

cha aar an

              Dialed            Total        Route    Call      Node
              String          Min    Max    Pattern   Type     Number

        186                    11     11     p2       aar
        188                    11     11     p2       aar
        189                    11     11     p2       aar
        3200                   4      4      9        aar
        59                     4      4      100      aar
        61                     4      4      100      aar
        65                     4      4      20       aar
        77                     4      4      100      aar
        82                     4      4      20       aar
        841                    4      4      20       aar
        842                    4      4      20       aar
        843                    4      4      20       aar
=====================================================================
list uniform-dialplan                                                  Page

                      UNIFORM DIAL PLAN TABLE

Matching Pattern   Len   Del   Insert Digits   Net    Conv   Node Num

3200                4     0                    aar     n
59                  4     0                    aar     n
61                  4     0                    aar     n
65                  4     0                    aar     n
77                  4     0                    aar     n
82                  4     0                    aar     n
841                 4     0                    aar     n
842                 4     0                    aar     n
843                 4     0                    aar     n
844                 4     0                    aar     n
845                 4     0                    aar     n
846                 4     0                    aar     n
847                 4     0                    aar     n
8480                4     0                    aar     n
8481                4     0                    aar     n


查看电话统计信息
list bcms trunk 6 day

添加mediapro板卡

F1退出,F3保存
分享到:
评论

相关推荐

    AVAYA CM配置

    读者范围主要是语音系统维护工程师,需要对AVAYA CM有基本的了解,并熟悉CM的基本操作和相关配置。 从上述内容中,我们可以总结出以下知识点: 1. AVAYA CM6系统配置:了解CM6的配置步骤,包括网关配置和CM数据...

    avaya语音交换机基本诊断手册

    - **诊断手册**主要包含了Avaya Communication Manager的基本故障排除方法,包括但不限于: - **网络连接问题**:检查网络配置、确认IP地址设置是否正确。 - **呼叫质量问题**:分析回声、噪音等问题的原因,并...

    avaya基本命令

    Avaya基本命令大全 Avaya程控交换机基本命令大全是Avaya程控交换机的基本命令手册,对于不熟悉命令的人,此文档可以用来参考。下面是Avaya程控交换机基本命令大全的详细知识点: 一、基本数据配置 * COR(Class ...

    avaya常规配置

    Avaya是一种知名的通信系统,常用于企业级的电话网络配置,包括S8300、S8500和S8700等型号。这些系统提供了丰富的功能,以...以上是Avaya系统的一些基本配置和功能,实际应用中会根据企业的具体需求进行定制和调整。

    AVAYA 9611话机 user guide

    8. 配置和设置:手册中提供了配置和设置指南,帮助用户正确地配置和设置 AVAYA 9611 话机。 AVAYA 9611 话机 User Guide 是一份非常实用的手册,能够帮助用户快速了解和掌握 AVAYA 9611 话机的操作和维护方法。

    AVAYA 命令全集及解释

    "8300 使用手册.pdf"可能是一个针对AVAYA 8300系列通信平台的操作指南,其中详细列出了该系列产品的使用方法和管理步骤。用户可以通过手册学习如何通过CLI执行常见的配置任务,如设置电话分机、配置VoIP参数、管理...

    AVAYA JTAPI SDK 6.3

    在开发过程中,开发者需要熟悉JTAPI接口提供的类和方法,理解Avaya通信系统的架构,以及如何利用SDK中的文档和示例代码。同时,还需要掌握Java编程和网络通信的基本知识,以便将JTAPI功能无缝地融入到应用程序中。

    AVAYA命令使用大全

    《AVAYA命令使用大全》 AVAYA是全球知名的通信...通过熟练掌握这些命令和配置方法,可以高效地管理AVAYA交换机,确保企业通信系统的稳定运行。在实际操作中,结合使用AVAYA提供的帮助和表单,能进一步提升工作效率。

    cisco &Avaya; IP trunk Interaction

    配置H.323 IP中继通常需要了解一些基本的管理步骤,包括如何设置网络设备,如Cisco 2948 Catalyst Switch和Cisco 3660路由器,以及如何在Avaya设备和Cisco VOIP网关(GW)之间正确配置参数。文档中提到了一个示例...

    AVAYA IPO500语音交换机产品详细

    - **易于管理**: 提供直观的图形用户界面(GUI),简化配置和日常维护。 ### 3. 功能特性 - **呼叫记录**: 记录通话细节,便于后期分析和改进服务。 - **队列管理**: 实时监控座席状态,优化呼叫处理效率。 - **报告...

    Avaya IP 电话快速设置指南 .pdf

    Avaya IP 电话快速设置指南主要面向的是使用Avaya IP Office 5610电话系统的用户,该指南提供了电话的基本功能和高级特性设置方法。Avaya IP Office是一款企业级通信解决方案,它支持IP电话、语音邮件、呼叫中心等...

    AVAYA中文编程资料

    #### 一、AVAYA系统基本配置与操作 AVAYA作为全球领先的通信解决方案提供商,其设备配置与管理涉及广泛的指令与参数设定,以下将详细介绍AVAYA系统中关键配置项及其操作命令。 ##### 1. 交换机基本数据配置 - **...

    AVAYA Cajun交换机使用手册

    用户模式提供基本的查看功能,特权模式增加了更多的配置选项,而超级用户模式则允许执行更高级的管理和维护任务,如更改系统设置、添加用户、恢复出厂配置等。 部分常用命令包括: - session:进入路由配置模式或...

    AVAYA ERS 2500,4500,5000系列交换机培训文档.doc

    总结起来,AVAYA ERS系列交换机的培训文档涵盖了设备概述、接入方法、基本维护、配置和高级特性等多个方面,旨在帮助管理员掌握全面的设备操作与管理技能,确保企业网络的高效运行。了解并熟练掌握这些知识对于任何...

Global site tag (gtag.js) - Google Analytics