xl2tp 中继器

参考https://haoningabc.iteye.com/admin/blogs/2517083

aws的redhat8搭建的xl2tp不能直接连ios了，不知道为什么，是8的问题还是aws的问题？
目前用腾讯云的centos7作为xl2tp的中转：
ios连centos7 ，centos7上搭建xl2tp的客户端和服务端，客户端连接aws的redhat8的xl2tp


关键问题注意4:

前提

ios：192.168.2.128

tx
eth0:172.17.0.13
ppp0:172.17.0.13 --->192.168.1.99
ppp1:192.168.2.99---->192.168.2.128

aws：
外网 13.115.114.179 
eth0:172.31.12.85 
ppp0:192.168.1.99 --->172.17.0.13

1.注意1400
两个xl2tp

ifconfig eth0 mtu 1400
ifconfig ppp0 mtu 1400
ifconfig lo mtu 1400

所有可见的地方全1400
1500似乎有时候有问题
/etc/xl2tpd/xl2tpd.conf--->/etc/ppp/options.xl2tpd 设置mtu和mru为 1400



2.注意 promisc ，
tx和aws 两个 eth0 和两个 ppp0都需要
ifconfig eth0 promisc
ifconfig ppp0 promisc

3.iptables

tx ：
iptables -t nat -A POSTROUTING -s 172.17.0.0/24  -o eth0  -j MASQUERADE
iptables -t nat -A POSTROUTING -s 192.168.2.0/24  -o ppp0  -j MASQUERADE
aws:
iptables -t nat -A POSTROUTING -s 172.17.0.0/24  -o eth0  -j 
 MASQUERADE

注意这里 虽然aws的本机段式172.31.12.85
这个操作是把ppp0 后面的 tx的ip段 172.17.0.13 做了snat
snat原理参考：
https://blog.csdn.net/jk110333/article/details/8229828



4.ip route

客户端连 server的时候
route del default 的时候就断网了（这个是关键问题）
需要

route add -host 13.115.114.179 dev eth0
如果是加网段：
route add -net  117.136.38.0 netmask 255.255.255.0 dev eth0

用这个方式把固定需要接入tx的ios和远程ssh的客户端ip全加进来，否则后续都连不上了
三个ip地方确认： 1. aws的server，2.ssh客户端ip 3.ios 客户端的ip


5.系统 没有firewalld 有NetworkManager


6.sysctl -p /etc/sysctl.conf

7. xl2tpd
tx作为客户端，和服务端
客户端需要配置lac testvpn ，具体的链接密码放在/etc/ppp/peers/aws.l2tpd
注意，配置完systemctl start  xl2tpd可能启动不了，重启才行，是内核模块的问题？


xl2tpd的配置 客户端需要

[lac testvpn]
lns =  13.115.114.179
pppoptfile = /etc/ppp/peers/aws.l2tpd
ppp debug = yes
[global]
force userspace = yes

服务端需要

[global]
ipsec saref = no
force userspace = yes

具体设置：

##################
基本安装：

dnf install https://dl.fedoraproject.org/pub/epel/epel-release-latest-8.noarch.rpm 
dnf install screen
dnf install libreswan xl2tpd  NetworkManager-l2tp -y  
yum install iptables nc  -y
telnet不能检测udp端口，用nc检测
nc -vuz 13.115.114.179 4500

##########################
配置xl2tpd
tx 客户端配置：
vim /etc/xl2tpd/xl2tpd.conf

[lac testvpn]
;name = root
;lns = 13.114.212.191
;lns =  52.196.182.31
lns =  13.115.114.179
;pppoptfile = /etc/ppp/peers/testvpn.l2tpd
pppoptfile = /etc/ppp/peers/aws.l2tpd
ppp debug = yes

[global]
;ipsec saref = no
force userspace = yes
; listen-addr = 192.168.1.98
;
; requires openswan-2.5.18 or higher - Also does not yet work in combination
; with kernel mode l2tp as present in linux 2.6.23+
; ipsec saref = yes
; Use refinfo of 22 if using an SAref kernel patch based on openswan 2.6.35 or
;  when using any of the SAref kernel patches for kernels up to 2.6.35.
; saref refinfo = 30
;
; force userspace = yes
;
; debug tunnel = yes

[lns default]
ip range = 192.168.2.128-192.168.2.254
local ip = 192.168.2.99
require chap = yes
refuse pap = yes
require authentication = yes
name = LinuxVPNserver
ppp debug = yes
pppoptfile = /etc/ppp/options.xl2tpd
length bit = yes

tx作为客户端角色的自配置，主要配置用户名和密码；
/etc/ppp/peers/aws.l2tpd

remotename testvpn
user "root"
password "Haohao123"
unit 0
nodeflate
nobsdcomp
noauth
persist
nopcomp
noaccomp
maxfail 5
debug

tx作为服务端服务端角色的子配置，主要mtu和mru 设置1400
/etc/ppp/options.xl2tpd

ipcp-accept-local
ipcp-accept-remote
ms-dns  8.8.8.8
noccp
require-mschap-v2
auth
idle 1800
mtu 1400
mru 1400
nodefaultroute
debug
proxyarp
connect-delay 5000

aws端的xltpd的配置：
/etc/xl2tpd/xl2tpd.conf
只加了
[global]
ipsec saref = no
force userspace = yes

内容为：

[global]
ipsec saref = no
force userspace = yes
; listen-addr = 192.168.1.98
;
; requires openswan-2.5.18 or higher - Also does not yet work in combination
; with kernel mode l2tp as present in linux 2.6.23+
; ipsec saref = yes
; Use refinfo of 22 if using an SAref kernel patch based on openswan 2.6.35 or
;  when using any of the SAref kernel patches for kernels up to 2.6.35.
; saref refinfo = 30
;
; force userspace = yes
;
; debug tunnel = yes

[lns default]
ip range = 192.168.1.128-192.168.1.254
local ip = 192.168.1.99
require chap = yes
refuse pap = yes
require authentication = yes
name = LinuxVPNserver
ppp debug = yes
pppoptfile = /etc/ppp/options.xl2tpd
length bit = yes

aws的xl2tpd服务端的子配置
/etc/ppp/options.xl2tpd

ipcp-accept-local
ipcp-accept-remote
ms-dns  8.8.8.8
ms-dns  1.1.1.1
# ms-dns  192.168.1.1
# ms-dns  192.168.1.3
# ms-wins 192.168.1.2
# ms-wins 192.168.1.4
noccp
auth
#obsolete: crtscts
idle 1800
mtu 1400
mru 1400
nodefaultroute
debug
#obsolete: lock
proxyarp
connect-delay 5000
# To allow authentication against a Windows domain EXAMPLE, and require the
# user to be in a group "VPN Users". Requires the samba-winbind package
# require-mschap-v2
# plugin winbind.so
# ntlm_auth-helper '/usr/bin/ntlm_auth --helper-protocol=ntlm-server-1 --require-membership-of="EXAMPLE\\VPN Users"'
# You need to join the domain on the server, for example using samba:
# http://rootmanager.com/ubuntu-ipsec-l2tp-windows-domain-auth/setting-up-openswan-xl2tpd-with-native-windows-clients-lucid.html

关于ipsec的配置：
tx上 没有改/etc/ipsec.conf
新增；/etc/ipsec.d/l2tp-ipsec.conf

conn L2TP-PSK-NAT
    rightsubnet=0.0.0.0/0
    dpddelay=10
    dpdtimeout=20
    dpdaction=clear
    encapsulation=yes
    also=L2TP-PSK-noNAT
conn L2TP-PSK-noNAT
    authby=secret
    pfs=no
    auto=add
    keyingtries=3
    rekey=no
    ikelifetime=8h
    keylife=1h
    type=transport
    left=172.17.0.13
    leftprotoport=17/1701
    right=%any
    rightprotoport=17/%any

left为本机eth0的ip
这里没有配置nexthop，不知道是否需要

aws上的ipsec的配置：
没有改/etc/ipsec.conf
新增：
/etc/ipsec.d/l2tp-ipsec.conf

conn L2TP-PSK-NAT
    rightsubnet=0.0.0.0/0
    dpddelay=10
    dpdtimeout=20
    dpdaction=clear
    forceencaps=yes
    also=L2TP-PSK-noNAT
conn L2TP-PSK-noNAT
    authby=secret
    pfs=no
    auto=add
    keyingtries=3
    rekey=no
    ikelifetime=8h
    keylife=1h
    type=transport
    left=172.31.12.85
    leftprotoport=17/1701
    right=%any
    rightprotoport=17/%any

和tx类似：
left为本机eth0的ip


#####################
密码文件：

tx：
/etc/ipsec.d/default.secrets

:   PSK "Haohao123!"
aws:

: PSK "Haohao123"

tx:
cat /etc/ppp/chap-secrets
root    *   haha123 *

aws:
cat /etc/ppp/chap-secrets
# Secrets for authentication using CHAP
# client	server	secret			IP addresses
root	*	Haohao123  *

这两个结合一下
ipv4.sh:

#!/bin/sh
for each in /proc/sys/net/ipv4/conf/*
do
    echo 0 > $each/accept_redirects
    echo 0 > $each/send_redirects
done

/etc/sysctl.conf

net.ipv4.ip_forward = 1  
net.ipv4.conf.all.accept_redirects = 0  
net.ipv4.conf.all.rp_filter = 0  
net.ipv4.conf.all.send_redirects = 0  
net.ipv4.conf.default.accept_redirects = 0  
net.ipv4.conf.default.rp_filter = 0  
net.ipv4.conf.default.send_redirects = 0  
net.ipv4.conf.eth0.accept_redirects = 0  
net.ipv4.conf.eth0.rp_filter = 0  
net.ipv4.conf.eth0.send_redirects = 0  
net.ipv4.conf.lo.accept_redirects = 0  
net.ipv4.conf.lo.rp_filter = 0  
net.ipv4.conf.lo.send_redirects = 0


sysctl -p /etc/sysctl.conf

ipsec verify

配置完xl2tpd 启动不了
重启init 6
试验一下 果然ok了

nc -vuz 13.115.114.179 4500

nc -vuz 13.115.114.179 1701


route add -host 81.68.183.137 dev eth0   
# route add -host 10.20.30.148 gw 10.20.30.40 


route add -host 13.115.114.179 dev eth0

最后
systemctl start ipsec
ipsec verify
检查
systemctl start xl2tpd



tail -f /var/log/message


ifconfig
ip route检查


客户端启动脚本：
checkppp0.sh

#!/bin/sh
ppp0=`ifconfig |grep ppp0`
if [ ! -n "$ppp0" ] ;then
    a="will start vpn"
    echo 'c testvpn' > /var/run/xl2tpd/l2tp-control
    sleep 5
    route del default
    ip link set ppp0 up
    /usr/sbin/route add default dev ppp0
    touch /opt/c
else
    ip link set ppp0 up
    /usr/sbin/route add default dev ppp0
    a="noting to do"
fi
/usr/sbin/ifconfig ppp0

echo $a
#route add -net  117.136.38.0 netmask 255.255.255.0 dev eth0
#ip route get 172.17.0.13