Xmanager在certos6.5配置（转）

[root@localhost gdm]# cat custom.conf

# GDM Configuration Customization file.

#

# This file is the appropriate place for specifying your customizations to the

# GDM configuration.   If you run gdmsetup, it will automatically edit this

# file for you and will cause the daemon and any running GDM GUI programs to

# automatically update with the new configuration.  Not all configuration

# options are supported by gdmsetup, so to modify some values it may be

# necessary to modify this file directly by hand.

#

# Older versions of GDM used the "gdm.conf" file for configuration.  If your

# system has an old gdm.conf file on the system, it will be used instead of

# this file - so changes made to this file will not take effect.  Consider

# migrating your configuration to this file and removing the gdm.conf file.

#

# To hand-edit this file, simply add or modify the key=value combination in

# the appropriate section in the template below.  Refer to the comments in the

# /usr/share/gdm/defaults.conf file for information about each option.  Also

# refer to the reference documentation.

#

# If you hand edit a GDM configuration file, you should run the following

# command to get the GDM daemon to notice the change.  Any running GDM GUI

# programs will also be notified to update with the new configuration.

#

# gdmflexiserver --command="UPDATE_CONFIG <configuration key>"

#

# e.g, the "Enable" key in the "[debug]" section would be "debug/Enable".

#

# You can also run gdm-restart or gdm-safe-restart to cause GDM to restart and

# re-read the new configuration settings.  You can also restart GDM by sending

# a HUP or USR1 signal to the daemon.  HUP behaves like gdm-restart and causes

# any user session started by GDM to exit immediately while USR1 behaves like

# gdm-safe-restart and will wait until all users log out before restarting GDM.

#

# For full reference documentation see the gnome help browser under

# GNOME|System category.  You can also find the docs in HTML form on

# http://www.gnome.org/projects/gdm/

#

# NOTE: Lines that begin with "#" are considered comments.

#

# Have fun!

 

[daemon]

 

[security]

 

[xdmcp]

 

[gui]

 

[greeter]

 

[chooser]

 

[debug]

 

# Note that to disable servers defined in the defaults.conf file (such as

# 0=Standard, you must put a line in this file that says 0=inactive, as

# described in the Configuration section of the GDM documentation.

#

[servers]

 

# Also note, that if you redefine a [server-foo] section, then GDM will

# use the definition in this file, not the defaults.conf file.  It is

# currently not possible to disable a [server-foo] section defined

# in the defaults.conf file.

 

这下发现，这个文件就是我要的配置文件。先备份（备份操作很重要），再开始设置相应的选项：

编辑/etc/gdm/custom.conf,内容如下：

[daemon]

[security]
AllowRemoteRoot=true

[xdmcp]
Port=177

[gui]

[greeter]

[chooser]

[debug]

[servers]

然后重启桌面：gdm-restart

 

设置防火墙，在/etc/sysconfig/iptables文件中加入：

-A RH-Firewall-1-INPUT -m state --state NEW -m tcp -p tcp --dport 6000:6010 -j ACCEPT
-A RH-Firewall-1-INPUT -m state --state NEW -m udp -p udp --dport 177 -j ACCEPT

重启防火墙：service iptables restart

在windows中启动Xmanager，就可以看到CentOS了。

 

 

在windows中启动启动Xstart，按下列提示输入：
Name: Xterm
Host: 192.168.1.4
procotol: SSH (setup port 为22)
User: xuys
Password: xuys1234

Execution Command可以填写/usr/bin/gnome-session --display=$DISPLAY,也可以填写  /usr/bin/xterm -display $DISPLAY 前者主要打开一个X桌面,后者只是打开一个xterm.根据需要自行选择.

点击“Save”，保存。
点击“Run”运行Xmanager。